REDMOTE Firmware

release history

VERSION 9.7.13

5.9 MB

Release Date:

6/1/2017

Release Notes

REDMOTE v9.7.13 Firmware June 1, 2017

IMPORTANT:

Please use the updated installers in the DSMC Resources package (Mac and Windows)
Camera Firmware v5.3.x or later is required to be functional.

Installation Instructions:

Windows instructions for manual network setup
– Open Internet Protocol (TCP/IP) properties for the REDmote connection (RNDIS Gadget)
– Select ‘Use the following IP Address’ and enter 192.168.0.1 with subnet mask 255.255.255.0. Click OK.
– Click OK to apply and exit Network Properties.
– Disconnect REDMOTE from the PC and wait 5 seconds.
– Reconnect REDMOTE to the USB Port and wait for Network to indicate connection
– Complete the REDMOTE Upgrade
– Restore the DHCP setting for the Network Connection after upgrade is complete
– Open Internet Protocol (TCP/IP) properties for the REDmote Connection (RNDIS Gadget)
– Select ‘Obtain an IP Address Automatically’ and select OK.
– Select Close to exit Network Properties.
– Disconnect REDMOTE from the PC
– Upgrade and system configuration is complete
Mac instructions for manual network setup
– Go to your Network and find the device titled RNDIS/Gadget.
– Select ‘Manually’, enter IP address 192.168.0.1 and Subnet Mask 255.255.255.0 and click Apply.
– Start REDmote Upgrade Utility and upgrade.
– Restore the DHCP setting after the upgrade is complete.
– Go to your Network and find the device titled RNDIS/Gadget.
– Select ‘Using DHCP’ and click Apply
– Upgrade and system configuration is complete
Contact RED if you are unable to connect using the manual instructions (http://www.red.com/contact_us).

Significant changes since previous build v9.7.12:

Added proxy recording baked-in settings support
Added per monitor LUT parameters support

Operational notes specific to build v9.7.13:

None

download

VERSION 9.7.12

5.9 MB

Release Date:

5/11/2017

Release Notes

REDMOTE v9.7.12 Firmware May 11, 2017

IMPORTANT:

Please use the updated installers in the DSMC Resources package (Mac and Windows)
Camera Firmware v5.3.x or later is required to be functional.

Installation Instructions:

Windows instructions for manual network setup
– Open Internet Protocol (TCP/IP) properties for the REDmote connection (RNDIS Gadget)
– Select ‘Use the following IP Address’ and enter 192.168.0.1 with subnet mask 255.255.255.0. Click OK.
– Click OK to apply and exit Network Properties.
– Disconnect REDMOTE from the PC and wait 5 seconds.
– Reconnect REDMOTE to the USB Port and wait for Network to indicate connection
– Complete the REDMOTE Upgrade
– Restore the DHCP setting for the Network Connection after upgrade is complete
– Open Internet Protocol (TCP/IP) properties for the REDmote Connection (RNDIS Gadget)
– Select ‘Obtain an IP Address Automatically’ and select OK.
– Select Close to exit Network Properties.
– Disconnect REDMOTE from the PC
– Upgrade and system configuration is complete
Mac instructions for manual network setup
– Go to your Network and find the device titled RNDIS/Gadget.
– Select ‘Manually’, enter IP address 192.168.0.1 and Subnet Mask 255.255.255.0 and click Apply.
– Start REDmote Upgrade Utility and upgrade.
– Restore the DHCP setting after the upgrade is complete.
– Go to your Network and find the device titled RNDIS/Gadget.
– Select ‘Using DHCP’ and click Apply
– Upgrade and system configuration is complete
Contact RED if you are unable to connect using the manual instructions (http://www.red.com/contact_us).

Significant changes since previous build v9.7.4:

Fixed stale clip list
Changed “P3” to “DCI-P3”

Operational notes specific to build v9.7.12:

None

download

VERSION 9.6.28

5.9 MB

Release Date:

7/29/2016

Release Notes

REDMOTE v9.6.28 Firmware July 29, 2016

IMPORTANT:

Please use the updated installers in the DSMC Resources package (Mac and Windows)
Camera Firmware v5.3.x or later is required to be functional.

Installation Instructions:

Windows instructions for manual network setup
– Open Internet Protocol (TCP/IP) properties for the REDMOTE connection (RNDIS Gadget)
– Select ‘Use the following IP Address’ and enter 192.168.0.1 with subnet mask 255.255.255.0. Click OK.
– Click OK to apply and exit Network Properties.
– Disconnect REDMOTE from the PC and wait 5 seconds.
– Reconnect REDMOTE to the USB Port and wait for Network to indicate connection
– Complete the REDMOTE Upgrade
– Restore the DHCP setting for the Network Connection after upgrade is complete
– Open Internet Protocol (TCP/IP) properties for the REDMOTE Connection (RNDIS Gadget)
– Select ‘Obtain an IP Address Automatically’ and select OK.
– Select Close to exit Network Properties.
– Disconnect REDMOTE from the PC
– Upgrade and system configuration is complete
Mac instructions for manual network setup
– Go to your Network and find the device titled RNDIS/Gadget.
– Select ‘Manually’, enter IP address 192.168.0.1 and Subnet Mask 255.255.255.0 and click Apply.
– Start REDMOTE Upgrade Utility and upgrade.
– Restore the DHCP setting after the upgrade is complete.
– Go to your Network and find the device titled RNDIS/Gadget.
– Select ‘Using DHCP’ and click Apply
– Upgrade and system configuration is complete
Contact RED if you are unable to connect using the manual instructions (http://www.red.com/contact_us).

Significant changes since previous build v9.6.22:

General bug fixes
Fixed 1.25x ICON in display
Fixed Motion Mount mode with no Motion Mount installed

Operational notes specific to build v9.6.22:

None

download

VERSION 9.6.22

5.9 MB

Release Date:

6/23/2016

Release Notes

REDMOTE v9.6.22 Firmware April 18, 2016

IMPORTANT:

Please use the updated installers in the DSMC Resources package (Mac and Windows)
Camera Firmware v5.3.x or later is required to be functional.

Installation Instructions:

Windows instructions for manual network setup
– Open Internet Protocol (TCP/IP) properties for the REDMOTE connection (RNDIS Gadget)
– Select ‘Use the following IP Address’ and enter 192.168.0.1 with subnet mask 255.255.255.0. Click OK.
– Click OK to apply and exit Network Properties.
– Disconnect REDMOTE from the PC and wait 5 seconds.
– Reconnect REDMOTE to the USB Port and wait for Network to indicate connection
– Complete the REDMOTE Upgrade
– Restore the DHCP setting for the Network Connection after upgrade is complete
– Open Internet Protocol (TCP/IP) properties for the REDMOTE Connection (RNDIS Gadget)
– Select ‘Obtain an IP Address Automatically’ and select OK.
– Select Close to exit Network Properties.
– Disconnect REDMOTE from the PC
– Upgrade and system configuration is complete
Mac instructions for manual network setup
– Go to your Network and find the device titled RNDIS/Gadget.
– Select ‘Manually’, enter IP address 192.168.0.1 and Subnet Mask 255.255.255.0 and click Apply.
– Start REDMOTE Upgrade Utility and upgrade.
– Restore the DHCP setting after the upgrade is complete.
– Go to your Network and find the device titled RNDIS/Gadget.
– Select ‘Using DHCP’ and click Apply
– Upgrade and system configuration is complete
Contact RED if you are unable to connect using the manual instructions (http://www.red.com/contact_us).

Significant changes since previous build v9.5.36:

Added v6.3 firmware support
Added Tint to Color Temperature label

Operational notes specific to build v9.5.37:

None

download

VERSION 2.0.14

5.72 MB

Release Date:

6/14/2012

Release Notes

REDMOTE v2.0.14 Firmware June 14, 2012

IMPORTANT:

You will not be able to roll back to earlier firmware revisions than v2.0.13 after installing v2.0.14
Camera Firmware v2.x or 3.0.x is required to be functional.

Installation Instructions for REDMOTE v2.0.14 firmware:

Please use installers (Mac and Windows) included in DSMC Toolkit package
Please refer to the Operations Guide included in download files for details and upgrade procedures.

Significant changes since build v2.0.13:

Fix for RIG and SYNC ICONs

download