SCARLET MYSTERIUM-X Firmware

DSMC Release Build v6.3.105 October 5, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.105.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.105 or v7.0.0 after upgrading to v6.3.105.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.105.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.105

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.104

• Fixed dismount method for 960GB REDMINI-MAG

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.105

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All Rights Reserved.

DSMC Release Build v6.3.104 August 30, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.104.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.104.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.104.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.104

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.102

• Added rear module upgrade failure notification
• Fixed RED Touch 4.7" LCD operation attached to side LCD/EVF port (DSMC2 only)
• Fixed SDI output on startup with framed overlay (DSMC2 only)
• Fixed intermittent media mount failure (DSMC2 only)
• Fixed gamma correction for RED Touch 7" LCD and DSMC2 EVF (DSMC2 only)
• Fixed ‘Proxy Buffer overflow’ with 4K HD R3D+DNxHR/HD (DSMC2 only)
• Fixed intermittent OMOD module firmware upgrade failure (DSMC2 only)
• Fixed Serial Communication dialog for OMOD RT modules (DSMC2 only)
• Fixed Amps in ‘Power Out’ for the DSMC2 V-Lock Battery Module Pro (DSMC2 only)
• Fixed camera shutdown with REDLINK Bridge Module attached (DSMC only)
• Fixed no LCD image on startup connected to Pro IO LCD/EVF port (DSMC only)
• Fixed displayed clip name of -- after exiting playback
• Fixed displayed Frame Rate after Project Time Base is changed
• Updated 8K VV calibration

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.104

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All Rights Reserved.

DSMC Release Build v6.3.102 June 1, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.102.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.102.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.102.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.102

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.101

• Added future RED accessory support
• Fixed Aperture scroll bar in the Lens Info dialog after lens swap
• Fixed incorrect clip list after media is formatted
• Fixed Apple ProRes ‘Buffer Overflow Error’ with 8K at 60fps
• Fixed ’Buffer Overflow ’ error with Avid DNx444 at high frame rate

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.102

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.3.101 April 18, 2017

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.3.101.
• You cannot downgrade a WEAPON, EPIC-W, SCARLET-W or REDRAVEN to earlier than v6.3.98 or v6.4.21 after upgrading to v6.3.101.
• You must upgrade your REDMOTE firmware to v9.6.×. Download the firmware upgrade from red.com/downloads.
• Refer to the Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Refer to https://support.red.com/hc/en-us/articles/225255907-DSMC-Module-Errors if you experience DSMC Side Handle issues after upgrading.
• Preset files created only on v4.0.x or later are compatible with v6.3.101.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.3.101

NOTE: User Preset, Look, and Custom Overlay files will be preserved across upgrades of v6.2.3 or later.

1. Connect an SSD (REDMINI-MAG or REDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

2. Download the most recent firmware from www.red.com/downloads.

3. Unzip the firmware zip file.

4. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

5. Eject or unmount the SSD, and then remove the SSD.

5. Ensure the camera is powered down and the REDMOTE is undocked.

6. Insert the SSD with the force_upgrade folder into your DSMC.

7. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

8. After the camera powers down, remove the SSD and wait 10 seconds.

9. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

10. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

11. Reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.3.98

• Added log_files directory
• Fixed HELIUM horizontal lines in image after calibration (DSMC2 only)
• Fixed Avid DNxHD/HR SQ quality (DSMC2 only)
• Fixed 8K HD record error at high frame rate (DSMC2 only)
• Fixed 25/50Hz HD-SDI output with test patterns or playback (DSMC2 only)
• Fixed missing timecode and frame rate in extended_clipinfo_t for ProRes and MXF clips (DSMC2 only)
• Fixed audio buffer oveflow errors with Apple ProRes 422/422LT (DSMC2 only)
• Fixed tearing in R3D for 3.5K 5:4 2x Anamorphic mode (DSMC2 only)
• Fixed Side Handle detection on startup (DSMC2 only)
• Fixed RCPMEDGCII response on record stop
• Fixed blank REDTOUCH 4.7" LCD after systems restore or upgrade
• Fixed calibration rename failure with special characters
• Fixed camera freeze applying guides in playback
• Improved HELIUM calibration (DSMC2 only)

OPERATIONALNOTESSPECIFIC TO BUILD v6.3.101

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• Do not 3D sync when GENICON is not illuminated or yellow.
• Image Magnify is available during preview only.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v6.0.46 February 2, 2016

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You must black shade an EPICDRAGON or SCARLETDRAGON after upgrading it.
• Upgrading your camera deletes all in-camera user-generated Preset, Look, and Custom Overlay files.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.0.46.
• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.0.46.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v6.0.46.
• You must upgrade your REDMOTE firmware to v9.3.×. Download the firmware upgrade from red.com/downloads.
• Refer to the REDDSMC Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v6.0.46.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v6.0.46

NOTE: You must black shade an EPICDRAGON or SCARLETDRAGON after upgrading it.
NOTE: Upgrading your camera deletes all in-camera user-generated Preset, Look, and Custom Overlay files.

1. If you have user-generated preset files on your camera, follow the instructions below to save the files to an SSD:
A. Power up the camera, insert an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") into the camera, and format the SSD.
B. Go to Menu > Presets and copy user-generated Camera Preset and Look files to the SSD.
C. Go to Menu > Settings > Display > Monitor Control and copy user-generated Overlay files to the SSD.
D. Shut down the camera, and remove the SSD. You will copy the files back to your camera after the upgrade procedure, as described in Step 13.

2. Connect an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

3. Download the most recent firmware from www.red.com/downloads.

4. Unzip the firmware zip file.

5. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

6. Eject or unmount the SSD, and then remove the SSD.

7. Ensure the camera is powered down and the REDMOTE is undocked.

8. Insert the SSD with the force_upgrade folder into your DSMC.

9. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

10. After the camera powers down, remove the SSD and wait 10 seconds.

11. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

12. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

13. To restore user-generated preset files to your camera, follow the instructions below:
A. Power up the camera and insert the SSD with the saved preset files into the camera.
B. Go to Menu > Presets and copy user-generated Camera Preset and Look files from the SSD to the camera.
C. Go to Menu > Settings > Display > Monitor Control and copy user-generated Overlay files from the SSD to the camera.

14. After upgrading an EPICDRAGON or SCARLETDRAGON, go to Menu > Settings > Maintenance > Calibrate > Sensor and black shade your camera using the Black Shading (default) option.

NOTE: You must black shade an EPICDRAGON or SCARLETDRAGON after upgrading it.

15. After offloading firmware upgrade files and/or preset files from any SSD, reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v6.0.44

• Fix camera not syncing on startup
• Fix camera freeze in 5K HD with Pro I/O Module

OPERATIONALNOTESSPECIFIC TO BUILD v6.0.46

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• You must black shade an EPICDRAGON or SCARLETDRAGON after upgrading it.
• Use camera BRAIN HD-SDI and Sync ports for 3D work
• Do not 3D sync when GENICON is yellow
• Camera powered by REDBRICK may display voltage instead of battery capacity on some cameras.
• EVF black level raised in some cases. Use Shadow adjustment as required.
• Image Magnify is available during preview only
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.

DSMC Release Build v5.3.49 December 18, 2015

NOTE: Download the latest versions of REDCINE-X PRO and the REDROCKET Installer or the REDROCKET-X Installer from red.com/downloads.

IMPORTANT:

• You must black shade an EPICDRAGON or SCARLETDRAGON after upgrading it.
• Upgrading your camera deletes all in-camera user-generated Preset, Look, and Custom Overlay files.
• You cannot downgrade an EPIC or SCARLETDRAGON to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v5.3.49.
• You cannot downgrade an EPICMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v5.3.49.
• You cannot downgrade an SCARLETMYSTERIUM-X to earlier than v5.3.49, v6.0.44 or v6.2.25 after upgrading to v5.3.49.
• You must upgrade your REDMOTE firmware to v9.0.x or later. Download the firmware upgrade from red.com/downloads.
• Refer to the REDDSMC Operation Guide, available at red.com/downloads, for REDMOTE upgrade instructions.
• Preset files created only on v4.0.x or later are compatible with v5.3.49.
• It can take the camera up to 8.5 minutes to update firmware for the RED Touch 7" LCD. The LCD displays a progress screen during the update. If your camera loses power during the update, turn your camera back on. The LCD upgrade restarts. During the upgrade, the LCD is blank and the PWR/REC LEDs flash green.

UPGRADEDSMCFIRMWARE TO v5.3.49

NOTE: You must black shade an EPICDRAGON or SCARLETDRAGON after upgrading it.
NOTE: Upgrading your camera deletes all in-camera user-generated Preset, Look, and Custom Overlay files.

1. If you have user-generated preset files on your camera, follow the instructions below to save the files to an SSD:
A. Power up the camera, insert an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") into the camera, and format the SSD.
B. Go to Menu > Presets and copy user-generated Camera Preset and Look files to the SSD.
C. Go to Menu > Settings > Display > Monitor Control and copy user-generated Overlay files to the SSD.
D. Shut down the camera, and remove the SSD. You will copy the files back to your camera after the upgrade procedure, as described in Step 13.

2. Connect an SSD (REDMINI-MAG or REDSTATIONREDMAG 1.8") to your computer.

NOTE: On Mac computers with REDCINE-X PRO installed, RED Watchdog mounts the SSD as Read-Only by default, which means that you are unable to write files (including firmware upgrade files) to the SSD. Change the Mount preference to Read-Write before attempting to copy firmware to the SSD.

3. Download the most recent firmware from www.red.com/downloads.

4. Unzip the firmware zip file.

5. Copy the force_upgrade folder and its contents to the top level of the SSD directory.

6. Eject or unmount the SSD, and then remove the SSD.

7. Ensure the camera is powered down and the REDMOTE is undocked.

8. Insert the SSD with the force_upgrade folder into your DSMC.

9. Power up the DSMC.

The upgrade automatically runs at power up.
During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera powers down. Nothing displays on the external monitors during the upgrade.

10. After the camera powers down, remove the SSD and wait 10 seconds.

11. Power up the camera.

The camera may take 30 seconds or longer to upgrade all the attached modules. During this time the PWR and REC LEDs flash green and nothing displays on the external monitors.

12. Go to Menu > Settings > Maintenance > System Status > Camera Info and verify that the firmware version listed matches the firmware version that you downloaded.

13. To restore user-generated preset files to your camera, follow the instructions below:
A. Power up the camera and insert the SSD with the saved preset files into the camera.
B. Go to Menu > Presets and copy user-generated Camera Preset and Look files from the SSD to the camera.
C. Go to Menu > Settings > Display > Monitor Control and copy user-generated Overlay files from the SSD to the camera.

14. After upgrading an EPICDRAGON or SCARLETDRAGON, go to Menu > Settings > Maintenance > Calibrate > Sensor and black shade your camera using the Black Shading (default) option.

NOTE: You must black shade an EPICDRAGON or SCARLETDRAGON after upgrading it.

15. After offloading firmware upgrade files and/or preset files from any SSD, reformat the SSD before recording to it.

SIGNIFICANTCHANGESSINCEPREVIOUSBUILD v5.3.47

• Fix intermittent image ‘jitter’ on RED Touch 7" LCD
• Fix LCD refresh on hot plug in ‘Mirror LCD’ mode

OPERATIONALNOTESSPECIFIC TO BUILD v5.3.49

• Secure Format media before using Pre-Record.
• The horizon feature requires Gyro calibration be completed prior to use.
• You must black shade an EPICDRAGON or SCARLETDRAGON after upgrading it.
• Use camera BRAIN HD-SDI and Sync ports for 3D work
• Do not 3D sync when GENICON is yellow
• Camera powered by REDBRICK may display voltage instead of battery capacity on some cameras.
• EVF black level raised in some cases. Use Shadow adjustment as required.
• Image Magnify is available during preview only
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Copyright © 2004-2017 RED.COM, LLC. All rights reserved.